New IP Data Highlights Multiple High-Priority Targets
Released
Released
Announcement PDF
ASX ANNOUNCEMENT – 24th
November 2025
New IP Data Highlights Multiple High-Priority Targets
Across a Potentially Large Intrusive System
Litchfield Minerals Limited (ASX: LMS) (“Litchfield” or “the Company”) is pleased to announce that it
has completed the first phase of the Induced Polarisation (IP) program across the VT2 and Northeast
Oonagalabi trend through to the Bomb Diggity intrusion. The survey comprised eight IP lines, each
~1.5km long, using 75m dipole spacing to penetrate deeper into the Oonagalabi system and support
the refinement of structural and mineralisation models.
The Oonagalabi Formation in the main zone plunges to the northeast where it disappears under folded
cover. As we have consistently inferred, this ‘prospective mineralised horizon’ wraps around the nose
of the broader Oonagalabi Anticline where it is interpreted to extend to VT2 and down to the VT1
prospect 6km to the southwest. The new IP results strongly support this interpretation where the
Oonagalabi Main Zone chargeability anomaly has been extended 450m to the northeast and two,
+500mlong, sub-parallel chargeability anomalies havebeen identified immediately adjacent to theVT2
conductor (Figure 1).
Figure 1 - Pole-Dipole Induced Polarisation Chargeability 2D Inversion sections, looking southwest, showing the
Oonagalabi Main Zone on the right where it plunges deeply under the Bomb Diggity area in the nose of the
Oonagalabi Anticline and then wraps around to the eastern limb of the anticline at VT2 where it is open to the
northeast.
Due to timing constraints with the consultants, we completed roughly half of the planned survey
coverage. The Company will return to complete the remaining IP lines in the next field window.
Combined with VTEM, DHEM and drilling data, this IP program continues to strengthen our conviction
that Oonagalabi represents a substantial mineralised corridor with multiple high-priority drill targets
emerging.
VT2 IP Commentary
The induced polarisation (IP) response at VT2 is consistent with expectations for a sulphide-rich system
as the survey has delineated large, coherent zones of low resistivity. This is a characteristic response
where interconnected sulphide mineralsprovide anefficient electrical conduction pathway,makinglow
resistivity a typical signature of semi-massive to massive sulphide accumulations. Importantly, these
low-resistivity domains are not restricted to the near surface but persist to depth, possibly suggesting a
laterally and vertically extensive sulphide-bearing package.
The (IP) campaign has also defined two, +500m long, sub-parallel zones of moderate chargeability (to
15mV/V)immediatelyadjacenttotheVT2DHEMmodelledplates(Figure2). Thechargeabilityanomaly
is interpreted to represent disseminated sulphides within the Oonagalabi Formation within the eastern
limb of the Oonagalabi Anticline.
Figure 2 – IP data illustrating the strong correlation between resistivity lows (blues and greens) and the modelled
VTEM plates, highlighting additional mineralisation potential open to the north and south, and likely continuing at
depth.
The IP survey has been effective at identifying zones of potential new mineralisation that were not
readily apparent in our existing magnetics, VTEM and DHEM datasets. The zones of semi-massive and
massivesulphides(pyrrhotite,sphalerite,chalcopyrite), whichweintersectedinOGRC0111
(edgeofthe
modelled VTEM plate), are interpreted to represent a potential higher-grade feeder structure to the
mineralised Oonagalabi Formation at VT2. Importantly, the VT2 prospect is completely preserved with
no erosion or evidence for mineralisation at surface. This validates the need to extend IP to the north
to determine the limits of the Oonagalabi Formation within the nose of the anticline and to the
southeast of VT2 to extend this zone down the eastern limb of the anticline (Figure 2).
Figure 2 - IP Chargeability 2D inversion sections, looking southwest, showing chargeability extending 450m
northeastfrom the OonagalabiMain Zone,plunging at depth under the Bomb Diggityprospectand thenwrapping
around to near-surface at the VT2 prospect. Also shown are the modelled DHEM plates and OGRC011.
More broadly, the emerging interpretation is that the wider Oonagalabi system may form part of a
significantly larger, intrusive-related sulphide system. Within this model, disseminated mineralisation
hosted within the Oonagalabi Formation represents the distal fluid outflow zone above and lateral to
the main intrusive drivers of the system at depth.
New data continues to support the interpretation that significant zones of potentially mineralised
Oonagalabi Formation exist at depth and that the broader system has mostly been preserved from
erosion. Thenew3DinversionoftheVTEMmagneticdatashowssomeofthemainmagneticanomalies
extending to +900m below surface and indicating that the system is vertically extensive.
1
ASX Announcement – 28th October 2025- DHEM Confirms Large Conductive Body at VT2.
Managing Director’s Comment
“This first phase of IP has changed the way we look at VT2 and the broader Oonagalabi corridor. We
are now seeing continuous chargeability and resistivity data that links the Oonagalabi Main Zone
through Bomb Diggity and into VT2, with multiple +500m long trends emerging immediately adjacent
totheVT2conductors. Whenyoucombinethatwiththesemi-massivetomassivesulphidesintersected
in OGRC011 on the edge of the VTEM plate, the new magnetic data indicating a corkscrew-shaped
interpreted intrusion rising out of the structural corridor between the Aileron and Irindina formations,
and coincident VTEM anomalies, it is hard to avoid the conclusion that we may be dealing with an
intrusion-related, vertically extensive sulphide system at depth that remains largely untested.
What is particularly compelling is that VT2 is completely blind at surface and yet the IP, VTEM, DHEM
and drilling are now all pointing to the same corridor of mineralisation, open along strike and at depth.
The new 3D magnetic inversion shows key magnetic bodies extending to nearly a kilometre below
surface and the IP is lighting up disseminated sulphides aboveand around those interpreted intrusions.
For our shareholders, this means we now have a growing pipeline of high-priority drill targets within a
system that appears to be both preserved and large-scale.
The next phase is straightforward. We will tighten up the geophysics with ground EM, complete the
remainingIPcoverageandthenbringthedrillrigsbackusingarefinedtargetingmodel. Ourrapid,data-
driven approach at Oonagalabi is doing exactly what we set out to do, compress the time between
concept and decision, build conviction with every program and give ourselves the best possible chance
of delivering a material discovery.”
Next Steps
• Ground EM acquisition commencing late November 2025.
• Data integration and modelling immediately following.
• Targeted drilling to begin once further holes are approved and after the integrated
interpretation, with precise collar positions refined by the new conductor models.
Cautionary Statement
This announcement contains forward-looking statements that involve known and unknown risks,
uncertainties, and other factors that may cause actual results, performance, or achievements to differ
materially from those expressed or implied. Such statements include but are not limited to,
interpretations of geophysical data, planned exploration activities, and potential mineralisation
outcomes. Visualestimatesofmineralabundance andpXRFresultsshouldneverbe consideredaproxy
or substitute for laboratory analyses where concentrations of grades are the factors of principal
economic interest. Visual estimates also potentially provide no information regarding impurities or
deleterious physical properties relevant to valuation. Forward-looking statements are based on
Litchfield Minerals Limited’s current expectations, beliefs, and assumptions, which are subject to
change in light of new information, future events, andmarket conditions. While the Company believes
that such expectations and assumptions are reasonable, they are inherently subject to business,
geological, regulatory, and operational risks. Further work, including drilling, is required to determine
the economic significance of any anomalies identified. Investors should not place undue reliance on
forward-looking statements. Litchfield Minerals Limited disclaims any obligation to update or revise
any forward-looking statements to reflect events or circumstances after the date of this
announcement, except as required by law.
About Litchfield Minerals
Litchfield Minerals is a critical mineral explorer, primarily searching for base metals and uranium out of
the Northern Territory of Australia. Our mission is to be a pioneering copper exploration company
committed to delivering cost-effective, innovative and sustainable exploration solutions. We aim to
unlockthefullpotentialofcopperandothermineralresourceswhileminimisingenvironmentalimpact,
ensuringthelongevityandaffordabilityofthisessentialmetalforfuturegenerations. Wearededicated
to involving cutting-edge technology, responsible practices and stakeholder collaboration drives us to
continuously redefine the industry standards and deliver value to our investors, communities and the
world.
The announcement has been approved by the Board of Directors.
For further information please contact:
Matthew Pustahya
Matthew@litchfieldminerals.com.au
Follow us on:
www.litchfieldminerals.com.au
https://twitter.com/Litchfield_LMS
https://www.linkedin.com/company/litchfield-minerals-limited/
Competent Person’s Statement
The information in this announcement relates to Exploration Results and is based on, and fairly
represents, information and supporting documentation compiled by Mr Russell Dow (MSc, BSc Hons
Geology), a Competent Person who is a Member of the Australian Institute of Mining and Metallurgy
(AUSIMM) and is a full-time employee of Litchfield Minerals Limited. Mr Dow has sufficient sampling
experience that is relevant to the style of mineralisation and types of deposits under consideration and
to the activity being undertaken to qualify as a Competent Person as defined in the 2012 Edition of the
“Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves” (JORC
Code). MrDowconsentstothe inclusioninthePublic Report ofthemattersbasedon theirinformation
in the form and context in which it appears. With regard to the Company’s ASX Announcements
referenced in the aboveAnnouncement, the Companyis notaware of any new information or datathat
materially affects the information included in the Announcements.
JORC Code, 2012 Edition – Table 1 report
Section 1 Sampling Techniques and Data
(Criteria in this section apply to all succeeding sections.)
Criteria JORC Code explanation Commentary
Sampling
techniques
• Nature and quality of sampling (e.g. cut channels, random
chips, or specific specialised industry standard measurement
tools appropriate to the minerals under investigation, such
as down hole gamma sondes, or handheld XRF instruments,
etc). These examples should not be taken as limiting the
broad meaning of sampling.
• Include reference to measures taken to ensure sample
representivity and the appropriate calibration of any
measurement tools or systems used.
• Aspects of the determination of mineralisation that are
Material to the Public Report.
• In cases where ‘industry standard’ work has been done this
would be relatively simple (e.g. ‘reverse circulation drilling
was used to obtain 1 m samples from which 3 kg was
pulverised to produce a 30 g charge for fire assay’). In other
cases more explanation may be required, such as where
there is coarse gold that has inherent sampling problems.
Unusual commodities or mineralisation types (e.g.
The instruments and parameters used for the Pole-Dipole Induced
Polarisation survey are as follows:
• Data collected by Fender Geophysics
• Pole-dipole IP/Resistivity time series data was acquired with
V-Full Waver IP/Resistivity Receivers in a distributed pole-
dipole array read in both senses C>P & C<P and with the I-
Full Waver Current Recorder recording full wave form
transmission data.
• All Receivers and the full wave form Current Recorder are
manufactured by Iris Instruments of Orleans, France
(www.iris-instruments.com).
• Pole-dipole current in injection was via one (1x) GDD TX4
5000W/20A transmitter manufactured by GDD
instrumentation of Quebec Canada
(www.gddintrumentation.com).
• Transmitters were powered by one (1x) Kubota 9000W
Diesel Generator.
Criteria JORC Code explanation Commentary
submarine nodules) may warrant disclosure of detailed
information.
Pole-Dipole Data Acquisition
• Tx Electrode Type: Aluminium foil lined pit (Remote CA) &
10mm welded mesh (Forward CB)
• Rx Electrode Type: CuSO4 Non-polarising porous pot
• Tx wire Type: 2.5mm Cu conductor
• Rx wire Type: 1.5mm Cu conductor
• Rx Line spacing: 100m
• Rx Dipole spacing: 50m.
• Time Base: 2s ON/2s OFF
• Windows: 20
• Timing Windows (ms):
20/20/20/20/40/40/40/40/80/80/80/80/
120/120/120/120/180/180/180/180
• mDelay (ms): 70
Instrument technical specifications
• Tx Receivers:
• Iris V-Fullwaver Receiver
• Channels: 2
• Input voltage: Max. input voltage: 15V, Protection: up to
1000V
• Voltage measurement: Accuracy: 0.2%, typical Resolution:
1µV, Minimum value: 1µV
• Input impedance: 100MΩ
Criteria JORC Code explanation Commentary
• Signal waveform: All IP measurements were made in the
time-domain using a two second half-duty cycle (2s ON/2s
OFF). An integration window of 0.5 to 1.1 seconds has
been used for the final chargeability calculation.
• GPS input for coordinates and synchronisation
• Computation of apparent resistivity, average chargeability,
and standard deviation
• Noise reduction: Read duration manually selected in
relation to apparent injection point current (mA) and
power line rejection, SP linear drift correction.
• Iris I-Fullwaver Current Recorder
• Input current: +/- 25000mA (optional 6, 15 or 50A)
• Resolution / Accuracy: 0.1mA / 0.1%
• GPS: GPS input for coordinates and time synchronisation.
Time stamps record within an absolute accuracy of 250us.
• Readings: Current value
• Typically three (3x), 300 second (~75x cycle stacks) reads at
each injection point.
• GDD TX IV 5000 Transmitter
• Output Power: 0 to 5000W
• Input voltage: Standard 240V 50hz
• Output Voltage Range: 150V to 2400V
• Output Current: 30mA to 20000mA
• Transmission Cycle: ON+, OFF, ON-, OFF:
Criteria JORC Code explanation Commentary
• Timing: 1s, 2s, 4s, or 8s
• Data processed by FW Viewer Prosys III TQIP WinDisp
Res2D
Drilling
techniques
• Drill type (e.g. core, reverse circulation, open-hole hammer,
rotary air blast, auger, Bangka, sonic, etc) and details (e.g.
core diameter, triple or standard tube, depth of diamond
tails, face-sampling bit or other type, whether core is
oriented and if so, by what method, etc).
• No new drilling in this report.
Drill sample
recovery
• Method of recording and assessing core and chip sample
recoveries and results assessed.
• Measures taken to maximise sample recovery and ensure
representative nature of the samples.
• Whether a relationship exists between sample recovery and
grade and whether sample bias may have occurred due to
preferential loss/gain of fine/coarse material.
• No new drilling in this report.
Logging • Whether core and chip samples have been geologically and
geotechnically logged to a level of detail to support
appropriate Mineral Resource estimation, mining studies
and metallurgical studies.
• Whether logging isqualitativeorquantitativeinnature.Core
(or costean, channel, etc) photography.
• The total length and percentage of the relevant intersections
logged.
• No new drilling in this report.
Criteria JORC Code explanation Commentary
Sub-
sampling
techniques
and sample
preparation
• If core, whether cut or sawn and whether quarter, half or all
core taken.
• If non-core, whether riffled, tube sampled, rotary split, etc
and whether sampled wet or dry.
• Forall sample types,thenature,qualityandappropriateness
of the sample preparation technique.
• Quality control procedures adopted for all sub-sampling
stages to maximise representivity of samples.
• Measurestakentoensurethatthesamplingisrepresentative
of thein situ material collected, including for instance results
for field duplicate/second-half sampling.
• Whether samplesizes areappropriatetothegrainsizeof the
material being sampled.
• No new drilling in this report.
Quality of
assay data
and
laboratory
tests
• The nature, quality and appropriateness of the assaying and
laboratory procedures used and whether the technique is
considered partial or total.
• For geophysical tools, spectrometers, handheld XRF
instruments, etc, the parameters used in determining the
analysis including instrument make and model, reading
times, calibrations factors applied and their derivation, etc.
• Nature of quality control procedures adopted (e.g.
standards, blanks, duplicates, external laboratory checks)
and whether acceptable levels of accuracy (i.e. lack of bias)
and precision have been established.
• See survey configuration and system specifications above.
Criteria JORC Code explanation Commentary
Verification
of sampling
and assaying
• The verification of significant intersections by either
independent or alternative company personnel.
• The use of twinned holes.
• Documentation of primarydata,data entryprocedures,data
verification, data storage (physical and electronic) protocols.
• Discuss any adjustment to assay data.
• No new drilling in this report.
• Data detailed in this report has been reviewed and
processed by Rob Angus at Mitre Geophysics.
Location of
data points
• Accuracy and quality of surveys used to locate drill holes
(collar and down-hole surveys), trenches, mine workings and
other locations used in Mineral Resource estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic control.
• Lines were gridded by Fender Geophysics using a Garmin
Map 65 series GPS.
• Waypoints were recorded at every station using
GDA94/UTM.
Data spacing
and
distribution
• Data spacing for reporting of Exploration Results.
• Whether the data spacing and distribution is sufficient to
establish the degree of geological and grade continuity
appropriate for the Mineral Resource and Ore Reserve
estimation procedure(s) and classifications applied.
• Whether sample compositing has been applied.
• PDIP was completed on 8, northwest-southeast oriented
lines spaced between 200m and 300m apart.
• Line spacing is considered appropriate for the scale of the
Oonagalabi system.
Orientation
of data in
relation to
geological
structure
• Whether the orientation of sampling achieves unbiased
sampling of possible structures and the extent to which this
is known, considering the deposit type.
• If the relationship between the drilling orientation and the
orientation of key mineralised structures is considered to
• Survey lines were oriented perpendicular to known
structureandstratigraphiccontrols(OonagalabiFormation).
• No bias is expected.
Criteria JORC Code explanation Commentary
haveintroducedasamplingbias,thisshouldbeassessedand
reported if material.
Sample
security
• The measures taken to ensure sample security. • All data was collected under strict data security measures by
Fender Geophysics Pty Ltd.
Audits or
reviews
• The results of any audits or reviews of sampling techniques
and data.
• Data checks and processing reviews were undertaken daily
and at the completion of the program by the contractor.
• Review of the data was undertaken by an independent
consultant (Rob Angus, Mitre Geophysics).
JORC Code, 2012 Edition – Table 1 report
Section 2 Reporting of Exploration Results
(Criteria listed in the preceding section also apply to this section.)
Criteria JORC Code explanation Commentary
Mineral
tenement
and land
tenure status
• Type, reference name/number, location and ownership
including agreements or material issues with third parties
such as joint ventures, partnerships, overriding royalties,
native title interests, historical sites, wilderness or national
park and environmental settings.
• The security of the tenure held at the time of reporting along
with any known impediments to obtaining a licence to
operate in the area.
• Tenement includes Oonagalabi (EL32279) for a total of
145.3km2 and 46 sub-blocks.
• EL32279 is owned by Kalk Exploration Pty. Ltd., a 100%
ownedentityofLitchfieldMinerals Limited. Thetenement is
located approximately 125km northeast of Alice Springs on
pastoral leases.
• The tenement is in good standing and there are no known
impediments.
Exploration
done by
other parties
• Acknowledgment and appraisal of exploration by other
parties.
• A summary of previous EL32279 exploration and mining is
presented below:
• Oonagalabi was discovered in the 1930’s.
• In 1970, Russgar Minerals completed regional mag-rad
survey, VLF_EM survey, ground magnetic survey, single line
resistivity traverse and 14 drillholes.
• In 1971, Geopeko completed limited IP.
Criteria JORC Code explanation Commentary
• 1979, Amoco completed photo-interpretation, rock chip
sampling and drilling (8 holes).
• 1981 D’Dor Mining NL completed limited dipole-dipole IP.
• Between 1990 – 1996 on EL 6940 Clarence River Finance
Group explored for garnet in the Florence and Maud Creeks,
collecting 15 samples that averaged 4.4% garnet
• Between 1997 – 2000 on EL 9420 Clarence River Finance
Group completed garnet exploration north of Oonagalabi
EL32279. In 2007, ML 22624 was applied for to cover the
centralOonagalabidepositandsurroundingproximalalluvial
systems (outside 2025 bulk sampling area). No work was
completed and the ML was relinquished in 2019.
• Silex 2009 completed pole-dipole IP 1 x diamond hole.
Geology • Deposit type, geological setting and style of mineralisation. • The Oonagalabi-type mineralisation is considered to be
either skarn-related, sediment-hosted or carbonate
replacement with potential for high-grade remobilised
breccia zones similar to the Jervois deposit. EL32279 falls
within one of Geoscience Australia’s IOCG high potential
zones.
• The project lies within the Harts Range that represents a
package of multiply deformed and metamorphosed
sedimentary and igneous intrusive rock.
Criteria JORC Code explanation Commentary
Drill hole
Information
• A summary of all information material to the understanding
of the exploration results including a tabulation of the
following information for all Material drill holes:
o easting and northing of the drill hole collar
o elevation or RL (Reduced Level – elevation above sea
level in metres) of the drill hole collar
o dip and azimuth of the hole
o down hole length and interception depth
o hole length.
• Iftheexclusionofthisinformationisjustifiedonthebasisthat
the information is not Material and this exclusion does not
detract fromtheunderstandingof thereport,theCompetent
Person should clearly explain why this is the case.
• No new drillhole information in this announcement
Data
aggregation
methods
• In reporting Exploration Results, weighting averaging
techniques, maximum and/or minimum grade truncations
(e.g. cutting of high grades) and cut-off grades are usually
Material and should be stated.
• Where aggregate intercepts incorporate short lengths of
high grade results and longer lengths of low grade results,
the procedure used for such aggregation should be stated
and some typical examples of such aggregations should be
shown in detail.
• The assumptions used for any reporting of metal equivalent
values should be clearly stated.
• No data aggregation methods used.
Criteria JORC Code explanation Commentary
Relationship
between
mineralisatio
n widths and
intercept
lengths
• These relationships are particularly important in the
reporting of Exploration Results.
• If the geometry of the mineralisation with respect to the drill
hole angle is known, its nature should be reported.
• If it is not known and only the down hole lengths are
reported,thereshouldbeaclearstatementtothiseffect(e.g.
‘down hole length, true width not known’).
• No new drillhole information in this announcement.
Diagrams • Appropriate maps and sections (with scales) and tabulations
of intercepts should be included for any significant discovery
being reported These should include, but not be limited to a
plan view of drill hole collar locations and appropriate
sectional views.
• See figures within the main body of the announcement.
Balanced
reporting
• Where comprehensive reporting of all Exploration Results is
not practicable, representative reporting of both low and
high grades and/or widths should be practiced to avoid
misleading reporting of Exploration Results.
• All available relevant information is presented.
Other
substantive
exploration
data
• Otherexplorationdata,ifmeaningfulandmaterial,shouldbe
reported including (but not limited to): geological
observations;geophysicalsurveyresults;geochemical survey
results; bulk samples – size and method of treatment;
metallurgical test results; bulk density, groundwater,
geotechnical and rock characteristics; potential deleterious
or contaminating substances.
• See the main body of this report for all pertinent
observations and interpretations.
Criteria JORC Code explanation Commentary
Further work • The nature and scale of planned further work (e.g. tests for
lateral extensions or depth extensions or large-scale step-out
drilling).
• Diagrams clearly highlighting the areas of possible
extensions,including themain geological interpretationsand
future drilling areas, provided this information is not
commercially sensitive.
Future planned exploration includes:
• Ground EM and IP at VT1, VT2 and Oonagalabi – Bomb
Diggity corridor
• IP infill at Bomb Diggity, VT2 extensions, VT1
• Phase 3 RC drilling.
Share your feedback
Discover