Survey Defines Four Shallower Copper & Nickel Priority Areas
Released
Released
Announcement PDF
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 1 of 27
19November2026
LMS Survey Defines Four Shallower Copper
and NickelPriority Areas Around a Deep
Conductor
A large conductor on a projected mantle-tapping fault sits beneath the strongest gravity
feature, with four shallower conductors on, or near, the structures around it. The LMS
field team is on site this week to assess the geology at surface over these conductors.
HIGHLIGHTS
■ Four priority areas defined: the magnetotelluric (MT) and gravity surveys completed through
BHP Xplor across an area of about 1,100km² has defined four priority areas for follow up
orthomagmatic copper–nickel and hydrothermal copper exploration: IA1, IA2, MT4 and MT6.
■ Two deposit styles, one set of pathways: the areas are relevant to both orthomagmatic
copper–nickel sulphides, as found at the Blackadder and Baldrick prospects in the Lloyd
Gabbro, and hydrothermal copper, as found at the Basil deposit in the Riddock Amphibolite
(not held by Litchfield).
■ Deep conductor on a mantle-tapping structure: MT5, from about 3km to more than 5km
below surface, lies on the projected Mt Mary Fault beneath the most prominent gravity
feature, an association Vox Geophysics considers encouraging for a sulphide-bearing
interpretation. Graphite is the main alternative and MT5 is too deep to target directly.
■ Boundary conductors, IA1 and IA2: robust conductors on the Irindina–Aileron shear zone,
supported by induction-arrow data. IA1 connects to MT5 at depth. Neither has an associated
gravity high.
■ Conductors on gravity highs, MT4 and MT6: conductive zones in dense, potentially reactive
rocks, MT6 within the Riddock Amphibolite, with some evidence of connection to MT5. MT4
is constrained mainly by two stations and MT6 is poorly defined at this stage.
■ MT3: a broad, strong conductor not explained by cover; its subdued gravity response is less
supportive of a sulphide source and its origin is currently unresolved.
■ On the ground this week: field reconnaissance initiated to test the survey results, to be
followed by 3D gravity modelling to test whether MT5 is dense (which would favour sulphides)
and closer-spaced surveys aimed at turning the best conductors into drill targets.
■ Wider opportunity: Litchfield intends to apply the same approach across the eastern Irindina
as results, tenure, access and funding allow.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 2 of 27
Litchfield Minerals Limited (ASX: LMS) has received Vox Geophysics’ final interpretation1
of its Harts
Range magnetotelluric (MT) and gravity surveys in the Irindina Province, Northern Territory, completed
through BHP’s 2026 Xplor program.2
The surveys covered a program area of about 1,100km² with 101 MT
stations and 504 new gravity stations (Figure 1).
Figure 1: Wherethe search now focuses. The combined MT and tipper model at 500m, 1,500m and 5,000m below sea level.
Ground level is about 510–800m above sea level, so the top slice is roughly 1,000–1,300m below surface. Red is conductive
and blue is resistive, on a logarithmic scale. Solid outlines mark the priority areas IA1, IA2, MT4 and MT6 and the unresolved
conductorMT3;thedashedoutlinemarksthe deepconductor MT5. Outlines are approximate, afterVoxGeophysics(2026).
These are interpreted conductive features, not mineral discoveries.
Litchfield is exploring for two stylesof copperdeposits that rely on similar ingredients: a source of metal,
a pathway through the crust and rocks where sulphides can form and be trapped. In orthomagmatic
copper–nickel deposits, metal-bearing magma rises from the mantle and forms sulphides when it picks
up sulphur from the rocks around it. In hydrothermalcopper deposits, fluids moving along structures and
deposit copper sulphides in favourable layers, contacts and reactive rocks.
Litchfield’s earlier work found evidence of mantle-derived magmas, including the Lloyd event, which
hosts known nickel–copper–PGE sulphides at the Blackadder and Baldrick prospects (which are outside
the Company’s tenure).3
The Riddock Amphibolite, within the survey area, is associated with the Basil
copper–cobalt deposit, which is held by Typhon Minerals (not Litchfield).4
The newsurveysaddevidence forthepathway and possible locationswheresulphides couldhaveformed
or been trapped. The report’s interpreted structures are connecting the deep crust with the upper crust,
which could have carried both magmas and mineralising fluids. The results indicate that conductive
rocks may include sulphur-bearing rocks, although graphite could also explain the conductivity. IA1, IA2,
MT4 and MT6 are found where these features coincide (Figure 1): IA1 and IA2 on the Irindina–Aileron
boundary, and MT4 and MT6 in potentially reactive rocks with gravity highs, with MT6 within the Riddock
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 3 of 27
Amphibolite. All fourconductors are visible in themodel from about 500m below sea level, roughly 1,000–
1,300m below surface; noting this is a model level, not the top of each conductor or a drilling depth.
The result turns a belt-scale hypothesis into a short list of specific places to test for both magmatic
copper–nickel and hydrothermal copper sulphides. The next phase is staged: field reconnaissance and
modelling first, more detailed surveys only where the evidence strengthens, and drill testing only once
specific targets are defined. Conductivity can also come from graphite, saline fluids or clay, so the
conductors do not in themselves establish mineralisation; only further work and, ultimately, drilling can
show whether sulphides are present.
Managing Director, Matthew Pustahya, said:
“This is the result we hoped for from the Xplor program. By testing our Harts Range thesis across a
survey area of approximately 1,100km2, we have narrowed one part of a belt-scale exploration
opportunity to four priority areas for follow-up (Figure 2).
Our earlier work found evidence of metal-bearing magmas from the mantle in this region. The survey
now images the deep structures that could have carried them. MT5 sits on the projected line of a
mantle-tapping fault beneath the strongest feature in the gravity data, the kind of long-lived pathway
our model needs.
MT5 is too deep to drill, but when you follow the interpreted structures up, you come to some very
interesting shallower conductors: IA1 and IA2 on the Irindina–Aileron boundary, and MT4 and MT6
sitting on gravity highs. They could be sulphides and finding out what they are is now our priority.
Those structures matter for both of our models: nickel–copper sulphides from mantle magmas, and
hydrothermal copper of the kind found at Basil. MT6 sits within the same Riddock Amphibolite as
Basil.
We are clear that conductors have other possible explanations, and that only fieldwork, further
surveys and modelling, and ultimately drilling will tell us what is there. That is why our team heads to
site this week, while we model the gravity in 3D with the MT to test whether MT5 is dense. The aim is
to turn the best of these conductors into drill targets and put our next dollars where the evidence is
strongest.”
Why the results matter: two deposit styles, one set of pathways
The exploration opportunity lies where the key ingredients for orthomagmatic copper–nickel sulphide
deposits and hydrothermal copper deposits come together. The Harts Range survey tested just one of
these areas within Litchfield’s belt (Figure 2) and the Company considers that the results highlight the
prospectivity of the wider belt. Litchfield holds a further ~9,000km² of ground where the same approach
can be applied. Magma provides a potential source of metals and heat, while deep geological structures
provide pathways for magma and mineralising fluids. Interaction between sulphur-bearing rocks and
magmas can promote the formation of sulphides that collect copper and nickel, while favourable
structures and reactive rocks can help focus and trap copper carried by hydrothermal fluids. The
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 4 of 27
challenge is identifying where those sulphides may have accumulated and been preserved at explorable
depths (Figure 3).3
The table below sets out the evidence for each part of the model before the survey,
what the survey adds, and what is still to be established.
Figure 2: The area investigated. The regional map places the survey within Litchfield’s Harts Range ground; the detailed
map shows the measurement locations. The dataset comprises 101 MT stations, 504 new gravity stations and 272 regional
gravity stations. Coverage is uneven, with gravity measurements following access routes. Company tenure and
application status are detailed in Appendix 1. Geological outlines: NTGS; coordinates: GDA94 / MGA Zone 53.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 5 of 27
Figure 3: Geological evolution and Litchfield’s exploration model. PGN Geoscience’s interpretation shows basin formation
and magma intrusion, followed by burial, heating, deformation and uplift. Litchfield’s thesis is that deep structures
provided pathways for mantle-derived magmas to encounter potentially sulphur-bearing or reactive basin rocks. These
interactions may have helped sulphides form, collect copper and nickel, and accumulate in favourable contacts or magma
channels. Later deformation and uplift may have modified and exposed parts of that system. Exploration now focuses on
where these pathways and favourable rocks intersect, and whether sulphide accumulations were preserved at accessible
depths. The diagram provides a regional framework spanning different events; it does not establish mineralisation at the
new conductive areas. Previously reported by Litchfield.3
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 6 of 27
Ingredient Evidence before the survey What the survey adds Still to establish
Metal and heat
source: mantle-
derived magma
Isotope and age studies
identified four periods of
enriched-mantle magma within
250km radius of Oonagalabi,
including the Lloyd event, which
hosts nickel–copper–PGE
sulphides at Blackadder–Baldrick
not within LMS tenure)
Not directly tested by MT or
gravity
Whether intrusions of this kind
are present at the priority
areas, as a source of Cu and Ni,
or heat for hydrothermal fluids
Pathway for
magmas and fluids:
deep structures
PGN Geoscience structural
interpretation and 3D fault
model; reinterpretation of
regional MT and seismic data
Interpreted crustal-scale
structures dipping inwards from
both margins of the province,
connecting the conductive
middle and lower crust with the
upper crust; IA1 and IA2 on the
boundary shear zone
The interpretation assumes
crustal structure similar to a
seismic line 70km to the east
Sulphur source and
reactive rocks
Mapped rock packages, including
the Harts Range Group and
Riddock Amphibolite (NTGS)
A conductive province interior
that may include sulphidic
metasedimentary rocks; MT4
and MT6 in potentially reactive
rocks with gravity highs
Whether the conductivity
reflects sulphides, graphite,
saline fluids or clay
Trap: where
sulphides could
accumulate
Regional precedents: the Lloyd
Gabbro (nickel–copper–PGE) and
Basil (copper–cobalt, held by
Typhon Minerals)
Four defined areas where
interpreted pathways meet
potentially reactive rocks: IA1,
IA2, MT4 and MT6
Untested. A significant
accumulation could be smaller
than the current surveys can
resolve
How MT and gravity see below the surface
MT (Magnetotelluric) surveys use naturally occurring electrical and magnetic fields to measure the
electrical resistivity of rocks beneath the surface. Low resistivity indicates high conductivity and vice
versa. Some sulphide accumulations are highly conductive, making MT useful for identifying deeper
targets for investigation beyond the typical reach of conventional EM (electromagnetic) techniques.
However, other materials, including graphite and saline water, can produce similar responses.
Gravity surveys measure small changes in the Earth’s gravitational field caused by differences in the
density and distribution of rocks. It helps identify broad packages of denser rock and possible
boundaries between geological units. In this setting (Figure 4), a gravity high may reflect amphibolite or
a dense intrusion; gravity alone cannot determine whether any rock contains mineralisation.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 7 of 27
Figure 4: The gravity framework. Left: Complete Bouguer Anomaly, where warmer colours are relatively higher gravity
values. Right: residual gravity, which suppresses broad regional trends to enhance shorter-wavelength features from
near-surface density variations, with less noise amplification than derivative products. This gives a clearer picture of
geological trends for comparison with mapped geology and interpreted structures. Labels mark the gravity features
defined by Vox Geophysics: G1, the prominent east–west gravity ridge coinciding with the resistive band MT1; G2, a central
gravity high with no corresponding MT feature; G3, subdued gravity associated with MT3; and G4, a gravity high associated
with MT4. G5, marked on the left panel, is the most prominent feature in the upward-continued gravity data and overlies
MT5. 776 gravity stations gridded at 250m; processing parameters are given in Survey details. Images: Vox Geophysics;
feature labels after Vox Geophysics (2026).
What the survey found
Vox Geophysics’ combined MT and tipper model divides the survey area into three electrical domains that
match the major rock packages:
• Southern region: predominantly resistive, comprising the Strangways Metamorphic Complex,
Riddock Amphibolite and Irindina Gneiss;
• Central region: conductive with the central Irindina Province; and
• Northern region: generally resistive encompassing the Harts Range Group and the adjacent
Aileron Province.
The interpreted resistivity boundaries dip inwards from both margins, consistent with the geological
model of an inverted rift basin for the Irindina Province.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 8 of 27
Following the structures up from MT5 across the major geological boundaries
The results are best read as a whole system rather than as individual anomalies (Figures 5 to 7). The deep
conductor MT5 lies on oneof the interpreted crustal-scale structures in the centre of the survey area and
the shallower conductors lie on or near the major structures and boundaries around it. The Vox
Geophysics’ model shows different degrees of connection between MT5 and the shallower conductors.
These range from a modelled connection at IA1 to possible connections at MT4, MT6 and MT3 that require
testing. Each feature is described below, starting at depth.
MT5 – The deep conductor
MT5 is a large conductor interpreted to extend from approximately 3km to more than 5km below surface,
aligned with the projected mantle-tapping Mt Mary Fault and Illogwa–Bruna Detachment (Figures 5 and
6). Its association with G5, the most prominent feature in the upward-continued gravity data, is
considered encouraging by Vox Geophysics for a possible sulphide-bearing interpretation. Sulphides
and/or graphite associated with a long-lived pathway for deep fluids and magmas are possible
explanations. The depth of the gravity source remains unresolved. The north–south banding likely
reflects an aligned (north–south) conductive fabric and station spacing, rather than separate bodies.
MT5 lies too deep to be a direct exploration target, however, Vox Geophysics considers it significant for
an improved understanding of potential mineral systems in this region.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 9 of 27
Figure 5: Following the conductors with depth. The top panel shows residual gravity; the panels below show successive
levels of the combined model from 500m above sea level to 5,000m below sea level. Solid outlines: shallow conductors;
dashed outline: MT5. A surface gravity response and a deeper conductor may be related without having identical outlines
or a single geological source. The panels are equally spaced for illustration, not to a true vertical scale.
IA1 and IA2 – Priority areas along a major geological boundary
IA1 and IA2 are two robust, south-dipping conductors along the northern Irindina–Aileron boundary,
supported by induction-arrow data. Both are visible in the 500m below-sea-level slice and extend to at
least 5km depth in the model (Figure 5). IA1 connects to MT5 at depth in Vox’s model and rises along the
boundary shear zone, which dips south at about 45–55° (Figure 6). PGN Geoscience’s 3D fault model
places the shallowest part of IA1 at the fault’s surface trace, and the strongest part of IA2 within 750m of
the modelled fault surface (Figure 7).5 IA1 and IA2’s position on a major geological boundary suggests
they may mark zones of focused fluid or magma movement. Neither is associated with a gravity high.
Figure 6 shows the north–south section along 475,000mE. Resistivity boundaries dip inwards from both
margins of the Irindina Province; MT5 lies on an interpreted structure in the centre of the province, and
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 10 of 27
IA1 lies along the south-dipping northern boundary. Vox Geophysics notes striking similarities with the
09GA-GA1 deep seismic line 70km to the east; its structural interpretation assumes that the crustal
structure hereresembles that imaged onthe09GA-GA1 seismic lineand is presented asa guideto further
investigation.
Figure 6: An inverted rift. North–south section along 475,000mE through the combined MT and tipper model to 12km below
sealevel,with residualgravity above. Black dashedlines: first-orderstructures;grey dashedlines: lesscertainstructures;
both after Vox Geophysics (2026), following the 09GA-GA1 seismic interpretation 70km to the east. Cyan lines: PGN
Geoscience’s 3D fault surfaces. Black contour: 30ohm metres. Triangles: MT stations within 1.5km.
MT4 and MT6 – Conductive features within favourable host rocks
MT4, in the Harts Range Group, and MT6, in the Riddock Amphibolite, are conductive relative to their
largely resistive surroundings and lie within potentially reactive rock packages. Both are associated with
gravity highs (Figure 5) and this combination warrants follow-up. There is some evidence of connection
to MT5 at about 5km depth along second-order structures, although this may reflect model smoothing
and needs to be confirmed by modelling. MT4 is constrained mainly by two stations; MT6 is subtle and
poorly defined. Additional MT stations or ground EM may be needed to define them better. Litchfield will
also assess whether MT6 could reflect Lloyd Gabbro-type intrusions within the Riddock Amphibolite.
Where the most prospective settings lie
Vox Geophysics identified the most prospective settings as those where the interpreted crustal-scale
pathways intersect potentially sulphur-bearing or reactive country rocks, such as sulphidic
metasedimentary rocks, (meta)carbonates or (meta)evaporites, including IA1, IA2, MT4 and MT6 (Figure
7). Litchfield considers these settings relevant to both its magmatic copper–nickel and hydrothermal
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 11 of 27
copper models. Whether sulphides accumulated in these settings is not yet known; the survey has
identified where to look, and field reconnaissance this week is the first step in testing them.
Figure 7: The conductors and the structures that overlap them. Combined MT and tipper model at 1,500m below sea level
with PGN Geoscience’s structural interpretation (shear zones, faults and magnetic trend lines) and the PGN 3D F7 fault
surface at 2km depth, showing its southward dip. Conductor outlines after Vox Geophysics (2026).
MT3 – Unresolved conductor in the central west
MT3 is a broad, strong conductor in the central west, modelled from about 500m below sea level to at
least several kilometres depth (Figure 5). It is supported by induction arrows, which are independent of
the modelling and provide a useful constraint. Vox Geophysics noted that MT5 potentially extends to
shallower depths in the west, towards MT3, though this is poorly defined. MT3’s deeper response is not
explained by expected shallow cover (Figure 8). No MT stations lie directly over it, so its geometry
remains poorly constrained. The subdued gravity response argues against a sulphide source but does
not resolve the conductor’s origin. MT3 therefore warrants further assessment as a separate
investigation opportunity alongside the four areas recommended for ground reconnaissance.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 12 of 27
Summary of the conductors
The table below summarises each feature: why it matters, how well the current data constrain it, and
what remains to be established.
Feature Why it matters How well constrained To be established
IA1 and IA2 Robust conductors on a major
tectonic boundary, potentially
marking focused fluid or magma
movement; IA1 connects to MT5.
Litchfield considers they could
reflect magmatic or hydrothermal
sulphides along the shear zone.
Robust; supported by
induction arrows; visible from
500m below sea level to at
least 5km in the model.
Whether mineralisation occurs
along or near these pathways.
Neither has an associated gravity
high.
MT4 and MT6 Conductive units within otherwise
resistive, potentially reactive rocks
associated with gravity highs, with
some evidence of connection to MT5.
MT6 lies within the Riddock
Amphibolite, which is associated
with the Basil deposit. Litchfield
considers they could reflect
magmatic or hydrothermal sulphides.
MT4 is constrained mainly by
two stations; MT6 is subtle
and poorly defined. Additional
MT stations or ground EM may
be needed to define them.
Conductor geometry, geological
source and possible connections to
MT5. Whether MT6 could reflect
Lloyd Gabbro-type intrusions
within the Riddock Amphibolite.
MT5 (deep
source)
Large deep conductor on a projected
mantle-tapping structure; its
association with the most prominent
gravity feature is encouraging for a
sulphide-bearing interpretation.
About 3km to more than 5km
below surface; north–south
banding likely reflects
conductive fabric and station
spacing.
Composition, depth of the gravity
source and whether the MT and
gravity features share a geological
source. Too deep for direct
targeting.
MT3 Broad, strong conductor supported
by the data and induction arrows; its
deeper response is not explained by
expected shallow cover.
No MT stations directly over it,
so its geometry is poorly
constrained.
Geometry and origin remain
unresolved. The subdued gravity
response is less supportive of a
sulphide source. Further
assessment is warranted.
Understanding shallow cover
Much of the central region lies beneath Cenozoic sand, alluvium and clay. Vox Geophysics’ 1D
probabilistic inversions show that most central-region stations have less than 100m of conductive cover
(Figure 8), however, cover may extend to several hundred metres at five stations, two of which overlap a
palaeochannel mapped by a 2006 HoisTEM airborne EM survey. Historical aircore holes intersected
mainly lacustrine clay (Appendix 2).6,7
Vox Geophysics interprets the shallow conductivity in the central region as largely caused by cover and
weathering, with this response potentially extending to greater depths due to smoothing in the MT
model.
Shallow cover does not explain the deeper MT3 response. Stations west of the main profiles show no
evidence of thick conductive cover and Vox Geophysics considered the MT3 response at approximately
500m below sea level and deeper is unexplained by cover.
IA1, IA2, MT4 and MT6 lie beneath areas of outcropping or subcropping rock, while MT5 lies kilometres
below the cover. The historical drilling characterises cover only; it did not test zones overlapping with
the MT conductors.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 13 of 27
Figure 8: Cover characterised. Left: conductance of the top 250m from the 2006 HoisTEM airborne EM survey (one-
dimensional models), with the 2007 aircore holes. Right: conductance of the top 1.5km of the combined MT model, on the
same colour scale. The two cover different depth ranges (250m and 1.5km), so they are compared for pattern rather than
value. Conductance, in siemens, is conductivity multiplied by thickness, summed over the depth range shown; it is the
property MT models resolve best, better than conductivity and thickness separately. Sources: NTGS open-file reports
CR2010-0895 and CR2008-0265.6,7
Two deposit styles: regional precedents
Riddock Amphibolite: a hydrothermal copper focus. A key regional example is the Basil copper–cobalt
deposit, drilled by Mithril Resources and now held by Typhon Minerals, which is associated with the
Riddock Amphibolite. Mithril reported a JORC Code 2004 Mineral Resource in 2012 of 26.5 Mt at 0.57%
copper and 0.05% cobalt.4
Basil has been interpretedas apossiblemetamorphosedvolcanogenic massive sulphide deposit, formed
by seafloor hydrothermal activity8
, although other ore-forming models remain plausible. Historical
reporting also records copper occurrences at Virginia and Selins within the Riddock Amphibolite, while
Sybil reporting describes conductive anomalies and anomalous surface samples associated with layered
Riddock Amphibolite.9,10
These occurrences support further exploration for hydrothermal copper sulphide mineralisation in
favourable layers, contacts and structures. They demonstrate regional copper potential, but do not
establish mineralisation within the new survey anomalies or throughout the Riddock Amphibolite (Figure
9). Basil is not held by Litchfield and the Company has not verified a Mineral Resource.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 14 of 27
Figure 9: Mantle-derived deposits and prospects, and regional structural context. The map brings together mantle-
derived mineral deposits and prospects and the interpreted structures used in the Company’s mineral systems
assessment. They span different ages (ca 1.8–0.4Ga) and deposit styles, including orthomagmatic Cu–Ni, Fe–Ti–V and
carbonatite-related mineralisation; most are not copper–nickel occurrences, and many are outside Litchfield tenure.
Jervois Fe-Ti-V prospects are located close to but not associated with the Jervois Cu-Ag deposits. The map shows where
mantle-derived mineralising processes are known to have operated in the region and help frame the search, rather than
establish mineralisation at the new targets.3
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 15 of 27
Lloyd and Coggans gabbros: an orthomagmatic copper–nickel focus. The ca. 0.4Ga Lloyd Gabbro
provides regional evidence of nickel–copper–PGE sulphide mineralisation, including at the Blackadder
and Baldrick prospects that are outside the Company’s tenure. The limited surface exposure of these
intrusions and their potential continuation beneath shallow cover support exploration for concealed
mineralised intrusive bodies.
The ca. 0.5Ga Coggans Gabbro represents an older, separate intrusive event and is also included in the
Company’s magmatic exploration model. Its fertility and relationship to any new exploration targets
remain to be established.11,12
Figure 9 plots all known mantle-derived deposits and prospects in the
region along with major lithospheric architecture, showing the potential for such systems regionally.
Many major orthomagmatic sulfide deposits occur in relatively small intrusions or magma channels
(Figure 10), which likely carried much larger volumes of magma over time. Research at Nova–Bollinger
nickel-copper mine documents one example of the importance of magma movement and sulphide
accumulation within a compact intrusive setting.13
Figure 10 illustrates the limited footprint of selected
host bodies and that an economic sulphide accumulation could occupy a small part of the broader
geological system and may not be separately resolved at the current geophysical survey spacing. The
regional results guide where more detailed work should be concentrated; the dimensions of the MT and
gravity anomalies are not estimates of an orebody.
Figure 10: Many major orthomagmatic deposits occur in compact host intrusions. The schematic from Beresford (2021)14
,
reproduced with permission, illustrates the limited footprint of selected host bodies; the graphic includes a 200m scale
bar. The comparison justifies the exploration model and the need for appropriately detailed geophysical surveys
undercover.
Litchfield Minerals Limited · www.litchfieldminerals.com.au Page 16 of 27
Next steps: how the results direct the next spend
The next phase is staged, so that each step is justified by the results of the one before. A target area
advances only if the evidence strengthens:
• Field reconnaissance (starting this week): inspect IA1, IA2,MT4, MT6 and other areas of interest
for surface evidence of prospective rocks, alteration and mineralisation. The results will decide
which areas proceed to modelling and follow-up surveys.
• Targeted modelling (proposed): 3D gravity and joint MT–gravity inversion to test whether MT5 is
dense, which would favour sulphides over graphite, and the relationship between G1 and G5, and
to assess MT3’s geometry, low-density association and possible geological sources. Integrate
these results with magnetic data and PGN’s structural model to determine appropriate follow-up
for MT3 and the other conductive areas.
• Follow-up surveys (proposed): closer-spaced gravity and MT, airborne EM or ground EM over
the strongest areas, withmapping, sampling androck-property measurements, to define targets
more accurately than the current surveys allow.
• Drill target selection: integrate the geological, sam
Share your feedback
Discover